济南手板模型加工的制造工艺

Manufacturing process of Jinan hand board model

1、通过手板模型加工设备依据程序设定的途径，在产品的原资料的基础上进行改动，得到手板模型加工的雏形。

1. The prototype of the hand model processing is obtained by modifying the hand model processing equipment based on the original data of the product according to the way of program setting.

2、手艺处理。在手板模型加工的雏形出来之后，样件的外观会有一些毛刺以及边角剩余的部分，工作人员应该用砂纸磨平，使得手板模型加工的外观变得润滑精美。

2. Process. After the prototype of the handboard model processing comes out, the appearance of the sample will have some burrs and the remaining parts of the edges and corners. The staff should use abrasive paper to smooth it, so that the appearance of the handboard model processing becomes smooth and beautiful.

3、镭雕，即是用激光技术打掉样件外观的油漆，使样件的一部分方位透光。

3. Laser carving is to use laser technology to remove the paint on the surface of the sample, so that part of the sample can be exposed to light in all directions.

4、氧化，即阳极处理，是行使电解的作用，因为处理过后构成的氧化的耐蚀性差、硬度低建网站费用，因而工艺进程中很少运用。

4. Oxidation, that is, anodic treatment, is used for electrolysis. Because the oxidation formed after treatment has poor corrosion resistance and low hardness, it is rarely used in the process.

5、拉丝，就是在铝合金的外观拉出一条条细痕，如许的处理会使样件的质感更好。

5. Wire drawing is to draw fine lines on the appearance of aluminum alloy. Such treatment will improve the texture of the sample.

断定选用手板模型加工的加工内容，断定工件的装置基面、加工基面、加工余量等，以充分发挥手板模型加工功率为意图来组织加工工序。关于复杂零件来说，因为加工进程中会发生热变形，淬火后会发生内应力，零件卡压后也会变形等多种原因，故全部工序很难在一次装夹后完结，这时能够考虑两次或多次装夹。

Determine the processing content of the handboard model processing center, determine the device base plane, processing base plane, processing allowance, etc. of the workpiece, and organize the processing process with the intention of giving full play to the power of the handboard model processing center. For complex parts, due to various reasons such as thermal deformation during processing, internal stress after quenching, and deformation after clamping, it is difficult to complete the whole process after one clamping. At this time, two or more clamping can be considered.

手板模型加工工序时应本着由粗渐精的准则。首要组织重切削、粗加工，去掉毛坯上的加工余量，然后手板模型加工工精度要求不高的内容。选用大流量的冷却方法，为削减加工时发生的大量热量对手板模型加工精度的影响，为进步刀具耐用度，需活跃选用大流量的冷却方法。您有需求就来我们网站http://www.axcwv.cn进行咨询吧！

The processing process of hand model should follow the principle of "from rough to fine". First, re-cutting and rough machining shall be organized to remove the machining allowance on the blank, and then the manual model shall be processed for the content with low accuracy requirements. The cooling method with large flow rate shall be selected. In order to reduce the impact of a large amount of heat generated during processing on the processing accuracy of the hand model, and to improve the tool durability, the cooling method with large flow rate shall be actively selected. Come to our website if you need http://www.axcwv.cn Consult!