在制作手板之前对手板进行设计对于提高手板质量是非常重要的，实际手板需要考虑到很多因素，如：手板材料的选用。下面济南手板厂家为您解说。

It is very important to design the hand board before making the hand board to improve the quality of the hand board. Many factors need to be considered in the actual hand board, such as the selection of hand board materials. Next, Jinan Prototype Factory will explain to you.

那么，手板在制作之前需要注意哪些问题呢？下面就由深圳市快速直接工业科技有限公司的产品负责人来简单讲解一下吧。

So, what problems should we pay attention to before making the prototype? Now let's have a brief explanation by the product director of Shenzhen Fast Direct Industrial Technology Co., Ltd.

手板材料的选用既要满足客户对产品质量的要求，还应当考虑到材料的成本及其在设计周期内的强度，同时还需根据手板的类型、使用的工作方式、加工速度、主要失效形式等因素来选择。

The selection of prototype materials should not only meet the customer's requirements for product quality, but also take into account the cost of materials and their strength in the design cycle. At the same time, it should also be selected according to the type of prototype, working mode, processing speed, main failure forms and other factors.

冲裁模的主要失效形式是刃口磨损，就需选择表面硬度高、耐磨性好的材料；冲压模主要承受周期性载荷，易引起表面疲劳裂纹，导致表面剥落，就要选择表面韧性好的材料；

The main failure form of blanking die is edge wear, so it is necessary to select materials with high surface hardness and good wear resistance; Stamping die mainly bears periodic load, which is easy to cause surface fatigue cracks and surface peeling, so it is necessary to select materials with good surface toughness;

拉伸模应选择摩擦系数特别低的材料；压铸模由于受到循环热应力作用，故应选择热疲劳性强的材料。

The drawing die shall be made of materials with very low friction coefficient; Because the die-casting die is subjected to cyclic thermal stress, the material with strong thermal fatigue should be selected.

手板上的各种零件应有足够的强度及刚度，防止使用过程中损坏和变形，手板上的各种零件应有足够的强度及刚度，防止使用过程中损坏和变形，紧固零件要有防松动措施，避免意外伤害操作者。不允许在加工过程中发生废料或工件飞弹现象，影响操作者的注意力，甚击伤操作者。另外要避免冲裁件毛刺割伤人手。

The various parts on the hand board shall have sufficient strength and stiffness to prevent damage and deformation during use. The various parts on the hand board shall have sufficient strength and stiffness to prevent damage and deformation during use. The fastening parts shall have anti loosening measures to avoid accidental injury to the operator. It is not allowed to produce waste materials or workpiece missiles during processing, which may affect the operator's attention or even injure the operator. In addition, the burrs of blanking parts shall not cut hands.

手板结构的可使用性及性、手板零件的可加工性及手板维修的方便性，这些在设计手板之初都应当尽量考虑得周全一些。更多相关内容就来我们网站http://www.axcwv.cn咨询吧！

The usability and safety of the prototype structure, the processability of the prototype parts and the convenience of the prototype maintenance should be considered as comprehensively as possible at the beginning of the prototype design. More relevant content will come to our website http://www.axcwv.cn Consult!